SuperMoto Junkie banner

Lets get a sticky for 510 jetting and ?'s!!!!!!!

53K views 74 replies 37 participants last post by  SMR510rider 
#1 ·
The 450 and 510 and becoming more popular and I think we all see the same questions being brought up. I also think if we have a Jetting Database this will help tremendously :thumbup:
I will post my Jetting later tonight.
Jetting should be recorded the same way by every SM junkie including Year,Alt, Mods, mj, pj, lj, air screw, and etc.
This way we can all help each other get the most out of our machines.
Let me know what you all think and maybe the MOD can get a sticky for us here :clap:
Thanks
Richie
 
#2 ·
good move. I just steal all of Coffee's data from TT. they have a pretty good list for husky's compiled
 
#5 ·
2007 510 SMR at 0 - 1000 ft elevation.
Bike has all emission restrictions removed
jetting coming tonite :)
 
#7 ·
2007 510 smr altitude 450-1200ft
oem pipe un corked
husky race jet
185 main
50 pilot
5th clip on needle
2 turns out fuel screw
 
#10 ·
thirty whats ur alt and temp. if close to mine then go with that. It runs ans starts awesome everytime, thats why I am scared to install the JD jetting it i have lol ! Why mes with something that aint wrong.
 
#11 ·
Thanks for the link, thats going to help a lot! ill get it figured out and post it on here when im done.

Im at basicly sea level to 150ft, moderate climate. the emissions is removed, full Akrapovic race pipe, K&N filter and a JD jet kit.
 
#12 ·
ok sounds good. Let me know I have the same setup and scared to install it for the same reasons u have. We seem to be same alt just what temps are u riding in? I want to install the JD jetting so bad. If both of us dial in our bikes it will be so helpful for the rest of SMJ with 450-510's
 
#14 ·
Heres what i got.

2007 SMR510, Altitude sea level - 150ft
-emissions removed
-full Akrapovikc race exhaust
-K&N air filter
JD jet kit
-Red Needle @ 5th clip
-180 main jet
-45 pilot
-air/fuel 1 3/4 turns
-leak jet
-thick O-ring

and yea... it still pops a little on decel, but thats the nature of the beast i guess.
 
#16 ·
Any jetting info on SM610's?

I bought my '06 husky sm610 used about three weeks ago. came with a leo vince full ti exhaust and jetting done by the dealer that the guy bought it from new. found the paper for the jetting instructions and this is what the dealer has written down that is supposed to be in it. main jet sounds really big but i dont really know if thats just me.

Main - 202
Pilot - 42
Needle - Red
Clip Position - 5th
Leak Jet - 70
Fuel Screw - 2 and 1/4th
Starter Jet - 85

any info would be cool. thanks.
 
#17 ·
I bought my '06 husky sm610 used about three weeks ago. came with a leo vince full ti exhaust and jetting done by the dealer that the guy bought it from new. found the paper for the jetting instructions and this is what the dealer has written down that is supposed to be in it. main jet sounds really big but i dont really know if thats just me.

Main - 202
Pilot - 42
Needle - Red
Clip Position - 5th
Leak Jet - 70
Fuel Screw - 2 and 1/4th
Starter Jet - 85

any info would be cool. thanks.
i also just put a k&n filter on the bike as well.
 
#20 ·
04 510
-sea level (below at times when I run it at Richmond.... :D) to maybe 400 feet so far.

-Completely stock setup for 04. That means competition flow through style muffler and no emmisions to need removing. The setup is dead stock other than the jetting.

-Bumped the main jet to a 190 and running the rest stock. It could likely use a lift of one slot on the needle since a few traces of lean shows up around idle and low throttle settings at lower RPM's like when cruising out to the track area. On the track it pulls strongly at all RPMs I'm using and doesn't show signs of any lean transition issues so I haven't bothered with fixing the lean issue when in the pits.

I tried the 180 and 185 and the bike was definetly running lean up top. Tested using the "roll off slightly from WFO and see what it does" method of looking for a little surge ahead to signify running a hair lean. The 190 seems rock solid for me.
 
#21 ·
I'm on par with the last guy, the rest of you make me feel good. Since my jetting is richer than all other 450's and some 510's! I have an '05 450 and when stock was running:
@ 800ft elevation in summer (like 90F)

185 main
50 pilot
Needle - one clip above middle (I move this when it's colder)
Air screw (or fuel, whatever) 1 3/4 turns out

I put a pro-circuit muffler and K&N intake on and now run:
185 main
50 pilot
Needle - one clip below middle (I move this when it's colder)
Air screw (or fuel, whatever) 1 1/4 turns out

This came with much pain, trial-and-error, and looking at spark plugs religiously. She is runnin like a dream. At one point I was up to a 55 pilot, but got some popping on decel, that was obviously too big. Also, if I go just one clip leaner on the needle, I start to get grey/white-ish plugs. So, I'm confident it's perfect for my bike. Did I mention she starts first or second kick every time (Except when hot of course!!!), usually without the choke! Maybe my ports just flow better than you lean guys (lucky me).
 
#22 ·
06 450

06 450 --- ~70 degrees @ sea level
thick o ring
full FBF exhaust
Sealed Exhaust

jd kit
180 main
45 pilot
Needle Red
clip 5th position
1.25 to 1.5 turns out

stillllll snap crackle pops on decel....

i have trouble believe that its not possible to get it to run w/o any pops on decel. I've tried using both a 175 and 185 main, neither with any success. would messing around with the pilot help
 
#27 ·
06 450 --- ~70 degrees @ sea level
thick o ring
full FBF exhaust
Sealed Exhaust

jd kit
180 main
45 pilot
Needle Red
clip 5th position
1.25 to 1.5 turns out

stillllll snap crackle pops on decel....

i have trouble believe that its not possible to get it to run w/o any pops on decel. I've tried using both a 175 and 185 main, neither with any success. would messing around with the pilot help

poping on decel is the pilot, not the main

try two to two and a half turns out on the pilot, if that doesnt fix it go bigger pilot
 
#23 ·
Mine pops on decel too (from high rpm usually not but always on low rpm). I don't know my jetting since the bike runs fine, starts fine and doesn't do anything funny when riding it. There's one problem though, I'm getting this weird studder at around 3800-4300rpm on like 1/8 throttle riding at constant speed. The higher the gear, the worse the studder is. Is there any way I can cure this? It is very annoying as I only can ride at certain constant speeds and in city traffic that's not very convenient. The studder 'stops' when I add a little throttle and the bike starts accelerating a bit. Above 4500rpm I never get that. Also when it studders I feel that the bike is vibrating more than usual and I can hear the drive chain rattle.
 
#25 ·
And you're being very helpful. I think I know enough about jetting as I've worked with 2-strokes a lot but what I'm really asking here is could that studder be caused by jetting issues (fuel screw, needle clip position?) or is it just because the bike isn't meant to be ridden at that rpm..?
 
#26 ·
2007 Husqvarna SMR510
stock gutted exhaust, stock filter, smog stuff removed
JD jet kit... 45 pilot, 180 main, 70 leak jet, thick o-ring, 5th clip JD red needle.
Air/fuel screw 1 3/4 turns out.

Live in between Sacramento and San Francisco (vacaville)... temps in the high 60's to low 90's.... 100-400 feet above sea level. Relatively dry.. 45-60% humidity.

Bike seems to run fine but does pop quite a bit under decel from 5-8k to close throttle positions. Also... from idle to whacking it open will bog down sometimes and even pop/then die. Bike idles fine at 1800-1950 rpm's, but at the recommended settings of 1700-1800 rpms's... it'll die when whacked open.

I've done lots of searching on here and TT on jetting and even made an excel spreadsheet on it and trying to dial it in perfectly.

So far.... I've changed out the pilot to a 42 and turned the a/f screw to 1 1/2 turns out and the popping/dying at idle to whack is for the most part gone. However, I've not addressed the backfiring issues at the higher rpm range.

Should I move the needle to the 6th position or maybe go with a 175 main? I'm hesitant to try anything else because I don't want to lean out the bike too much and have it running too hot/lean and start having heating/burning up problems.

Any suggestions here... don't think I left out anything.
 
#28 ·
read this flow chart

each item overlaps the other



so basically there four areas you need to get right to have your bike run the best

accel pump mods and changing pump cover affects throttle right off idle

taper of needle and clip in middle and main jet is mostly all top end full throttle

thats the basics
 
#31 ·
07 610 slip on & k&n
185 main
jd red 4th clip
45 pilot
thick o-ring
2.0 turns out on fuel screw
bike feels good throughout rpm range

had way to much bottom end with this set up
180 main
45 pilot
5th clip jd red
2.5 out on the fuel screw
leak jet. when i installed the leak jet the idle was all over the place. (1300-1900) i took it out when i went up to the 185 main and the bike idles at 1500 steady.
 
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top